CARA MENGONEKSIKAN MODEM SMART CE682 DI BACKTRACK 5

Pertama yang perlu disiapkan yaitu modem smart CE682 sama Operating sistem Backtrak.Setelah semua terpenuhi langkah selanjutkan cara mengoneksikan modem smartnya.

 Langkah-langkah mengoneksikan modem smartnya sebagai berikut:
 1.pertama chek apakah si modem sudah kedeteck di linux kita caranya ketik perintah "dmesg \tail" pada terminal. backtrack@nusution$ dmesg \tail [ 16.435959] ADDRCONF(NETDEV_UP): eth0: link is not ready [ 19.963390] EXT4-fs (sda7): re-mounted. Opts: errors=remount-ro,commit=0 [ 19.966436] EXT4-fs (sda8): re-mounted. Opts: commit=0 [ 241.704054] usb 2-2: USB disconnect, address 3 [ 253.352033] usb 2-2: new full speed USB device using uhci_hcd and address 4 [ 253.522675] scsi5 : usb-storage 2-2:1.0 [ 254.524252] scsi 5:0:0:0: CD-ROM CDROM EVDO ReV A 7.00 PQ: 0 ANSI: 2 [ 254.536216] sr1: scsi-1 drive [ 254.536454] sr 5:0:0:0: Attached scsi CD-ROM sr1 [ 254.536652] sr 5:0:0:0: Attached scsi generic sg2 type 5 terlihat modem kita sudah kedeteck tapi masih dalam mode CDROM jadi di eject biar ga kedeteck CDROM. backtrack@nusution:~$ sudo eject /dev/sr1 kemudian bisa dilihat dengan dmesg lagi backtrack@nusution:~$ dmesg | tail [ 137.553752] xhci_hcd 0000:04:00.0: WARN: short transfer on control ep [ 137.553988] xhci_hcd 0000:04:00.0: WARN: short transfer on control ep [ 137.554308] xhci_hcd 0000:04:00.0: WARN: short transfer on control ep [ 137.554587] xhci_hcd 0000:04:00.0: WARN: short transfer on control ep [ 137.554838] xhci_hcd 0000:04:00.0: WARN: short transfer on control ep [ 137.555060] scsi8 : usb-storage 3-1:1.3 [ 138.553271] scsi 8:0:0:0: Direct-Access SDVDISK EVDO ReV A 7.00 PQ: 0 ANSI: 0 CCS [ 138.613281] sd 8:0:0:0: Attached scsi generic sg3 type 0 [ 138.616649] sd 8:0:0:0: [sdc] Attached SCSI removable disk [ 184.204635] usbserial: `0×1022' invalid for parameter `product' Modem sudah terdeteksi dengan baik langkah selanjutnya kita chek modem dengan perintah backtrack@nusution:~$ lsusb Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 004 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub Bus 001 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub Bus 002 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub Bus 001 Device 004: ID 058f:a014 Alcor Micro Corp. Bus 001 Device 005: ID 0bda:0139 Realtek Semiconductor Corp. Bus 001 Device 006: ID 0cf3:3005 Atheros Communications, Inc. Bus 003 Device 005: ID 201e:1022 Ternyata telah kedeteck Bus 003 Device 005: ID 201e:1022 tapi nama vendornya tidak muncul tetapi tidak berpengaruh mari lanjut ke perintah selanjutnya : backtrack@nusution:~$ sudo nano /etc/usb_modeswitch.conf tambahkan kode dibawah baris yang terakhir dengan kode ######################################################## # /etc/usb_modeswitch.conf # # Smart Haier CE682 (EVDO) # DefaultVendor = 0x201e DefaultProduct = 0×1022 TargetVendor = 00x201e TargetProduct = 0×1022 MessageContent=”5553424312345678c00000008000069f030000000000000000000000000000″ lalu save dengan menekan ctrl+o dan ctrl+w kemudian masuk ke file konfigurasi ini : backtrack@nusution:~$ sudo nano /etc/udev/rules.d/99-haier-ce682.rules isi file dengan konfigurasi ini : ######################################################## # /etc/udev/rules.d/99-zte-ce682.rules # # Smart Haier CE682 (EVDO) # SUBSYSTEM==”usb”, SYSFS{idVendor}==”201e”, SYSFS{idProduct}==”1022″, RUN+=”/usr/sbin/usb_modeswitch –default-vendor 0x201e –defaultproduct 0×1022 –message-content 5553424312345678c00000008000069f030000000000000000000000000000″ lalu save dengan menekan ctrl+o dan ctrl+w sekarang load beberapa parameter yang dibutuhkan ke kernel backtrack@nusution:~$ sudo modprobe usbserial vendor=0X201e product=0X1022 kemudian beralih ke wvdial jadi bagi temen-temen yang di laptopnya belum terinstall wvdial bisa menginstallnya terlebih dahulu backtrack@nusution:~$ sudo apt-get install wvdial lalu edit file konfigurasinya di wahyulaptop@wahyu:~$ sudo nano /etc/wvdial.conf hapus semua file konfigurasi dalam file wvdial.conf dan ganti dengan ini : [Dialer smart] Init1 = ATZ Init2 = ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 Stupid Mode = 1 Modem Type = Analog Modem Command Line = ATDT ISDN = 0 New PPPD = yes Phone = #777 Modem = /dev/ttyUSB0 Username = smart Password = smart Baud = 460800 lalu save dengan menekan ctrl+o dan ctrl+w langkah terakhir coba koneksi dengan cara backtrack@nusution:~$ sudo wvdial smart --> WvDial: Internet dialer version 1.61 --> Cannot get information for serial port. --> Initializing modem. --> Sending: ATZ --> Sending: ATQ0 ATQ0 OK --> Re-Sending: ATZ ATZ OK --> Sending: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 OK --> Modem initialized. --> Sending: ATDT#777 --> Waiting for carrier. ATDT#777 CONNECT 3100000 --> Carrier detected. Starting PPP immediately. --> Starting pppd at Tue Mar 27 18:27:36 2012 --> Pid of pppd: 2144 --> Using interface ppp0 --> local IP address 10.158.165.xxx --> remote IP address 10.20.31.xxx --> primary DNS address 10.17.3.xxx --> secondary DNS address 10.17.3.xxx semoga bermanafaat...:D